Alpina B3 Flash

[bimmerwork]

Big shoutout and credit to @cn555ic


This guide is intended for personal use and anything that happens to your car is done soley by your choice.. This guide just provides the instructions on how to flash the software. I do not hold any responsibility if you damage your car.  



Alpina B3 Flash DIY using WinKFP 



DIY Guide to Flash Alpina B3 Flash: 



************************************************** **********************************

WARNING...If you dont know what your doing, dont be brave and blindly go into this advanced flashing of software into the TCU module.. If your not too confident in doing this, either pay someone or just do without it.....WinKFP is a very dangerous tool but yet its awesome and in terms of coding its pretty advanced.. Proceed after reading this warning if you choose to do so... 

************************************************** **********************************


This flash will make the transmission run smoother, gear change will be more precise and crisp, rev match downshift is unbelievable, rev limiter is increased and overall driveability is increased. You will have a new indicator for gear selection in D mode which display D1, D2, D3 ,D4, D5 and in DS mode you will see S1, S2, S3, S4, S5 and the same for the M mode. This single flash will make the car change gears more refined and crisp. You will no longer feel the lurching when the tranny shifts and it goes through the gears without even the slightest hesitation. It is indeed a must have flash if you own a E9x with a N54 engine...


This Alpina TCU flash works for model years 3/07 till present N54/N55 engine (some N55 engines which are rare, exhibit the rpms jumping down to zero on each shift but acts normal in every other way..This can be addressed if you update your DME version if you have this erratic rpm issue after flash). If your production date is before 3/07, your out of luck and cant flash your car! Before you attempt this you should have some knowledge in coding and setting software. You need to confirm INPA software is working and communicating with car. If you dont have INPA communicating, dont move beyond this point and go back and do some more research on getting it to work.. There are plenty of DIY guides for setting up INPA, Ediabas, NCSexpert and WinKFP,  


You can purchase a proven cable that works...Please dont ask will this one work as it is cheaper if so.. Buy one that is proven and it will save you alot of headaches!

http://www.one-stop-electronics.com/...&product_id=16



Once you have configured your laptop properly with INPA, NCSexpert and WinKFP, you need to download Spdaten 53.0 which I have provided a link to download a condensed form for the strict purpose of this Alpina flash. The link for the SPdaten 53.0 is not the entire version and doesnt have the other data files needed to flash other modules if you need them, this is strictly for Alpina flash which makes the download much quicker...

https://www.dropbox.com/s/sb0bm1he0j7hto9/53.0.rar



Follow the guide how to import the SPdaten 53.0 data into Winkfp by downloading the PDF I have provided below..Once you have the data imported into Winkfp then you need to configure the Winkfp..follow this





Once Winkfp is configured correctly your ready to begin the flash of your new Alpina B3 software into your car!!


IMPORTANT..For those using Procede or JB4 make sure the tune is set to VALET map 0 before you start the flash.. 

Here we go:

You have not unlocked this post's content yet. Please reply to this thread to unlock the content.

Have fun modding!

Dope

[castrol]

Big  shoutout  und Kredit @ cn555ic


Dieses Handbuch ist für den persönlichen Gebrauch und alles gedacht , die zu Ihrem Auto geschieht , ist getan soley von Ihrer Wahl .. Dieses Handbuch enthält nur die Anweisungen, wie die Software zu blinken. Ich übernehme keine Verantwortung, wenn Sie Ihr Auto beschädigen.  



Alpina B3 Flash DIY mit WinKFP 



DIY Leitfaden für Flash Alpina B3 Flash: 



************************************ ******************************************************

WARNING...If you dont know what your doing, dont be brave and blindly go into this advanced flashing of software into the TCU module.. If your not too confident in doing this, either pay someone or just do without it.....WinKFP is a very dangerous tool but yet its awesome and in terms of coding its pretty advanced.. Proceed after reading this warning if you choose to do so... 

************************************************** **********************************


This flash will make the transmission run smoother, gear change will be more precise and crisp, rev match downshift is unbelievable, rev limiter is increased and overall driveability is increased. You will have a new indicator for gear selection in D mode which display D1, D2, D3 ,D4, D5 and in DS mode you will see S1, S2, S3, S4, S5 and the same for the M mode. This single flash will make the car change gears more refined and crisp. You will no longer feel the lurching when the tranny shifts and it goes through the gears without even the slightest hesitation. It is indeed a must have flash if you own a E9x with a N54 engine...


This Alpina TCU flash works for model years 3/07 till present N54/N55 engine (some N55 engines which are rare, exhibit the rpms jumping down to zero on each shift but acts normal in every other way..This can be addressed if you update your DME version if you have this erratic rpm issue after flash). If your production date is before 3/07, your out of luck and cant flash your car! Before you attempt this you should have some knowledge in coding and setting software. You need to confirm INPA software is working and communicating with car. If you dont have INPA communicating, dont move beyond this point and go back and do some more research on getting it to work.. There are plenty of DIY guides for setting up INPA, Ediabas, NCSexpert and WinKFP,  


You can purchase a proven cable that works...Please dont ask will this one work as it is cheaper if so.. Buy one that is proven and it will save you alot of headaches!

http://www.one-stop-electronics.com/...&product_id=16



Once you have configured your laptop properly with INPA, NCSexpert and WinKFP, you need to download Spdaten 53.0 which I have provided a link to download a condensed form for the strict purpose of this Alpina flash. The link for the SPdaten 53.0 is not the entire version and doesnt have the other data files needed to flash other modules if you need them, this is strictly for Alpina flash which makes the download much quicker...

https://www.dropbox.com/s/sb0bm1he0j7hto9/53.0.rar



Befolgen Sie die Anleitung zum Importieren der SPdaten 53.0-Daten in Winkfp, indem Sie die unten bereitgestellte PDF-Datei herunterladen. Sobald Sie die Daten in Winkfp importiert haben, müssen Sie die Winkfp-





Datei konfigurieren Der Blitz Ihrer neuen Alpina B3-Software in Ihrem Auto!


WICHTIG. Wenn Sie Procede oder JB4 verwenden, stellen Sie sicher, dass die Melodie auf VALET Map 0 eingestellt ist, bevor Sie den Flash starten. 

Los geht's:

[verstecken] Inhalt ist versteckt! Bitte überprüfen Sie den Originalbeitrag, um ihn anzuzeigen. [/ Hide]
Viel Spaß beim Modden!

[kensys1]

Big shoutout and credit to @cn555ic


This guide is intended for personal use and anything that happens to your car is done soley by your choice.. This guide just provides the instructions on how to flash the software. I do not hold any responsibility if you damage your car.  



Alpina B3 Flash DIY using WinKFP 



DIY Guide to Flash Alpina B3 Flash: 



************************************************** **********************************

WARNING...If you dont know what your doing, dont be brave and blindly go into this advanced flashing of software into the TCU module.. If your not too confident in doing this, either pay someone or just do without it.....WinKFP is a very dangerous tool but yet its awesome and in terms of coding its pretty advanced.. Proceed after reading this warning if you choose to do so... 

************************************************** **********************************


This flash will make the transmission run smoother, gear change will be more precise and crisp, rev match downshift is unbelievable, rev limiter is increased and overall driveability is increased. You will have a new indicator for gear selection in D mode which display D1, D2, D3 ,D4, D5 and in DS mode you will see S1, S2, S3, S4, S5 and the same for the M mode. This single flash will make the car change gears more refined and crisp. You will no longer feel the lurching when the tranny shifts and it goes through the gears without even the slightest hesitation. It is indeed a must have flash if you own a E9x with a N54 engine...


This Alpina TCU flash works for model years 3/07 till present N54/N55 engine (some N55 engines which are rare, exhibit the rpms jumping down to zero on each shift but acts normal in every other way..This can be addressed if you update your DME version if you have this erratic rpm issue after flash). If your production date is before 3/07, your out of luck and cant flash your car! Before you attempt this you should have some knowledge in coding and setting software. You need to confirm INPA software is working and communicating with car. If you dont have INPA communicating, dont move beyond this point and go back and do some more research on getting it to work.. There are plenty of DIY guides for setting up INPA, Ediabas, NCSexpert and WinKFP,  


You can purchase a proven cable that works...Please dont ask will this one work as it is cheaper if so.. Buy one that is proven and it will save you alot of headaches!

http://www.one-stop-electronics.com/...&product_id=16



Once you have configured your laptop properly with INPA, NCSexpert and WinKFP, you need to download Spdaten 53.0 which I have provided a link to download a condensed form for the strict purpose of this Alpina flash. The link for the SPdaten 53.0 is not the entire version and doesnt have the other data files needed to flash other modules if you need them, this is strictly for Alpina flash which makes the download much quicker...

https://www.dropbox.com/s/sb0bm1he0j7hto9/53.0.rar



Follow the guide how to import the SPdaten 53.0 data into Winkfp by downloading the PDF I have provided below..Once you have the data imported into Winkfp then you need to configure the Winkfp..follow this





Once Winkfp is configured correctly your ready to begin the flash of your new Alpina B3 software into your car!!


IMPORTANT..For those using Procede or JB4 make sure the tune is set to VALET map 0 before you start the flash.. 

Here we go:

You have not unlocked this post's content yet. Please reply to this thread to unlock the content.

Have fun modding!

Thanks

[Borys3004]

thank you i will try

[M3Pat]

Big shoutout and credit to @cn555ic


This guide is intended for personal use and anything that happens to your car is done soley by your choice.. This guide just provides the instructions on how to flash the software. I do not hold any responsibility if you damage your car.



Alpina B3 Flash DIY using WinKFP



DIY Guide to Flash Alpina B3 Flash:



************************************************** **********************************

WARNING...If you dont know what your doing, dont be brave and blindly go into this advanced flashing of software into the TCU module.. If your not too confident in doing this, either pay someone or just do without it.....WinKFP is a very dangerous tool but yet its awesome and in terms of coding its pretty advanced.. Proceed after reading this warning if you choose to do so...

************************************************** **********************************


This flash will make the transmission run smoother, gear change will be more precise and crisp, rev match downshift is unbelievable, rev limiter is increased and overall driveability is increased. You will have a new indicator for gear selection in D mode which display D1, D2, D3 ,D4, D5 and in DS mode you will see S1, S2, S3, S4, S5 and the same for the M mode. This single flash will make the car change gears more refined and crisp. You will no longer feel the lurching when the tranny shifts and it goes through the gears without even the slightest hesitation. It is indeed a must have flash if you own a E9x with a N54 engine...


This Alpina TCU flash works for model years 3/07 till present N54/N55 engine (some N55 engines which are rare, exhibit the rpms jumping down to zero on each shift but acts normal in every other way..This can be addressed if you update your DME version if you have this erratic rpm issue after flash). If your production date is before 3/07, your out of luck and cant flash your car! Before you attempt this you should have some knowledge in coding and setting software. You need to confirm INPA software is working and communicating with car. If you dont have INPA communicating, dont move beyond this point and go back and do some more research on getting it to work.. There are plenty of DIY guides for setting up INPA, Ediabas, NCSexpert and WinKFP,


You can purchase a proven cable that works...Please dont ask will this one work as it is cheaper if so.. Buy one that is proven and it will save you alot of headaches!

http://www.one-stop-electronics.com/...&product_id=16



Once you have configured your laptop properly with INPA, NCSexpert and WinKFP, you need to download Spdaten 53.0 which I have provided a link to download a condensed form for the strict purpose of this Alpina flash. The link for the SPdaten 53.0 is not the entire version and doesnt have the other data files needed to flash other modules if you need them, this is strictly for Alpina flash which makes the download much quicker...

https://www.dropbox.com/s/sb0bm1he0j7hto9/53.0.rar



Follow the guide how to import the SPdaten 53.0 data into Winkfp by downloading the PDF I have provided below..Once you have the data imported into Winkfp then you need to configure the Winkfp..follow this





Once Winkfp is configured correctly your ready to begin the flash of your new Alpina B3 software into your car!!


IMPORTANT..For those using Procede or JB4 make sure the tune is set to VALET map 0 before you start the flash..

Here we go:

You have not unlocked this post's content yet. Please reply to this thread to unlock the content.

Have fun modding!

Thanks!

[Autotronica DGS]

thanks rob as always awesome

[relekexe]

Good, thank you

[pear]

i must check

[pranasj]

very informative, thank you

[aussiebimmer]

Thanks very much