Hi, I'm Teo from Italy, I have a BMW X1 F48 18d

Hello Bimmers Guys..
i have a BMW E60 2008, Stock is 520i when i bought, but i was Swapped Engine from N46B20 154hp 200nm to Black Cover N52B30AE
i google it for this engine, someone say is a 528i not 530i, means this engine output is 230hp 271Nm
and now i want to Power Up, i google it again someone say you can power up this Engine like 530i N53, Power goes up to 268hp 315Nm
but you need to install 3 Stage Intake Manifold and Flash DME with BMW X5 E70 3.0si because this N52 from this car has a 268hp 315Nm
for installing this intake, no problem i will buy it, but how can i Flash DME with X5 3.0si, to Enable Disa Valve
i have Standard Tools, ÎŜ†Ä, wth D-Can Cable

and This is my Acceleration Car with no Passenger and No Spare Tyre from Boot, and 102mAh Battery, with 20L Fuel Tank

0-100km/h 8.0s
0-160km/h 20.5s
0-200km/h 32.5s
1/4 Mile 15.8s

just i need a Flash File from this car
and if you know something and advice about this please tell me..
i know about Bimmerlabs, they have a File, 325i & 328i to 330i, but probably just for E90 91 92 93, i don't know it is different for E60 or not !
Thanks Guys.

Hello everyone, I used the swt-patcher kit from "123intel" to validate false FSCs and I therefore used the file via USB to virginize the CIC.

Following that, I wanted to flash the ecu to inject my own fscs.

I flashed the ecu with the latest i-step everything seemed ok, but after each restart the nav is grayed out and all my fscs rejected.

I noticed in ėšÝ§ when I check my fscs that a "SigSCertStatus" line is missing. Here is an image before where I managed to install a map and now the line is no longer there and the fscs are rejected after each restart..

Does someone have an idea ?

Hi, My name is Robert, I live in Poland. Not so long ago I became the owner of a BMW E39 530D from 2003. I came here looking for information about coding and general car diagnostics.

Hi all

In older versions I’ve had expert mode which allowed me to choose ecu’s I wanted to flash, rather than the whole car. Is this still possible with the newer versions, I think I have 4.39

Thanks

Status: I have Coded 5AS Driver Assist and I have everything close to functioning. 
Now I need a little help for the FDL coding of the last details - Anything, though it might seem small, is really helpful and apriciated!

The right button (Pic 1)for Lane departure warning (LDW), is not functioning. It should be like the picture.
But nothing happens when i press it and there is no green light. 
Also i cannot change setting for LDW in menu (Pic 3)

When i press the Left button (Pic 1), it tries to activate all driver assistance (Pic 2).
But like the picture says: All intelligent safety systems could not be activated. I can then choose config individual -> Redirects to Pic 3.

I think all systems are up and running. No errors on anything during testdrive. Manage to activate both FCW and LDW.

FSC´s are OEM and accepted.
Link to my Updated cafd: CAFD_00000A07_002_019_001.ncd
vin: wba8j91010k837585

Do you have the missing piece of the pussle? 
Maybe you can share your CAFDs or give instructions?
 Anything, though it might seem small, is really helpful and apriciated!


           

Hello everyone, I am from morocco, happy to be part of the community

Hello everyone, I am form Brazil, haapy to be part of the community and glad to help whenever I can!

Hi everyone from France. 

Hi everyone from Poland. I'm new here, but forum helped me a lot in the past. I hope that I can provide some help and share my knowledge here.