Hey Everyone, i recently picked up a 2017 440i and was referred to this page from a discord chat for updating my Infotainment Headunit to the latest Firmware
today i wanna share my resent retrofit with you.
Since i´m always looking for new retrofits i can do to my F20 pre-LCI, this time i wanted to add an rear view camera. Most people would tell me to check wich camerasystem my car expects with 3AG added to VO. Since i´m owning and old F20, it expects an TRSVC wich would be neccessery if i still had the CIC installed. Sadly the TRSVC ECU, CAM and wiring loom would cost me around 400€ used.
Because i already retrofitted an NBT Evo from an 2018 G11, there now are more options to use.
In my case, i chose to add an ICAM camera since this one has the controller integrated and so only needs some extra wires. The hard part was to find a suitable camera. After some research, i found the ICAM of an X5 F15 <11/2015 as suitable. This one works with FBAS and CAN3 on FEM. Additionaly you only need an BMW Evo retrofit wiring loom for X1/5/7 G/F Series ICAM2. Both together costed me around 170€ incl. shipping.
Since there are no housings for ICAM cameras to build into the F20 rear bumper, i had to create my own with a 3d printer from ABS. i added an Matching opening between the lincense plate lights and fixed the housing+camera there.
I put the cable through an plug that was already existing under the rear light on the driver side.
The red power wire was connected to fuse F154 (5A) in the rear fuse box since, this is meant to be used with camera.
the yellow/brown (CAN3_High) and yellow/red (CAN3_LOW) are connected to CAN2 of FEM. I can´t tell exactly why but CAN3 devices also work on CAN2 CAN3 and CAN2 use the same Baudrate and same messages. CAN3 ecus will read CAN2 messages and vice versa. ėšÝ§ and ÎŜ†Ä however won´t show ECUs that arent supposed to be on other bus lines. No ICAM/TRSVC entry in CAN2 table from F20 so no ICAM/TRSVC shown in ėšÝ§/ÎŜ†Ä even if it´s connected and working.
the FBAS wires are directly connected to the HU Quadlock. Green on 21, black on 23 and white on 24.
now the coding part.
at first you might get confused, since ė-šÝ§ won´t show the ICAM camera. Because of the gateway table, you won´t see the CAN3 device since it is not supposed to be connected to CAN2.
Like written above, you won´t be seeing the ICAM and so can´t code it but you can continue coding the rest. Create an VO with 3AG added and code HU_NBTevo and REM. Then just FDL code camerasystem from TRSVC to ICAM_rfk in HU_NBTevo
and that´s it. Now you should have an working ICAM on your retrofitted NBT Evo system
Edit: Update 10-02-2021 -> Proper Coding
After using this setup for a while, i got annoyed by the guiding lines. I have been driving without lines most of the time, because i am just used to park with mirrors instead. My family however prefer the guiding lines.
Somehow the camera coding "got lost" with the retrofit. Guess this happend because the donor car was an F39 and my car is an F20 both with different VIN. With the missing CAFD, on every ignition start the ICAM set itself to "default coding" but since there is no default coding for F20, it just chose an random model. So every time i used the cam with guiding lines, those linse looked differend. Sometimes small, sometimes thicker, sometimes disaligned and sometimes the turning cicle wouldn´t match.
After some research i found bill57p´s (Bimmerfest.com) retrofit guide for the F56. i rebuild this gateway, modified the code and adapted it to my F20. ÎŜ†Ä/ėšÝ§ showed the icam but ėšÝ§ couldn´t detect an CAFD for SWFL 1EE1_017_002_000. This is the shipping swfl and no PsDZ package contains an fitting CAFD file. I tried deploying one of the available CAFDs (017_004_000) but those got rejected half way.
So i had to update the ICAM to the latest ilevel with matching CAFD File. I learned the hard way, that this gateway is not suitable for flashing in my case. the flash will fail and set the car to transportmode. you´ll have to reset everything with ÎŜ†Ä in that case. wasted time...
last option. Flashing with an ZGW which has CAN3. i bought an used ZGW 8SK for around 50€, Placed an Arduino with an CAN shild and voltage regulator for the wakeup and the Ethernet activator inside the ZGW hosuing. Also an ethernetcable got hardwired into the housing.
Connecting the ZGW to 12V will automatically start it and activate ethernet communication. Connected power to my car battery and CAN3 with ICAM. ėšÝ§ showed ZGW and ICAM2. Now i only had to flash latest ilevel with CAFD. Created an VO from donor car (F39) and my VIN and flashed ICAM.
for an F20 you should use an F39 VO because the F39 is what comes closest to an F20 in size and camera position. Otherwise lines and camera angle wouldn´t match.
After flashing i only had to make some minor changes. Screensize had to be changed to widescreen in ICAM CAFD and calibration startet via Tool32. Lastly deleted all DTC and my ICAM retrofit was finaly finished.
Hi, This questions is just for my E series coding.
Where do I put the folders DATA and DATA-SWI for ISTAP programming?
I have tried finding this info since days but couldn't. There are many threads and they are all different regarding RHEINGOLD folder, symbolic links, some say put them here c:\ProgramData\BMW\ÍŠÞÍ\data\TRIC\ others say into ISTAD folder, some say into a dedicated folder called PSDZ. I am confused and want to understand how that works.
The PDF ÎŜ†Ä guide says into the ISTAD folder under PSDZ. But how does ISTAP know where to find those files? Do I need ISTAD installed at all for ISTAP? I don't want to use symbolic links. Can I verify before programming with ISTAP that all files are where they supposed to be?
Hello everyone. I`m from Serbia and I`m a civil engineer, but I love to learn something more, like coding BMW, diagnostic, maps update etc.. I drive a BMW 520d n47 from 2008. I hope to have a nice time here on forum. Thanks
Hi guys had my 320d remapped on a dyno, it achieved 230bhp, I’m having a couple of problems and was wondering if it’s possible to ‘download’ the remapped files from the vehicle and revert to standard whilst diagnostics takes place. Also where would I find a standard map for my car?
