xHP Flashtool - Printable Version +- Bimmer Scene - Latest BMW Coding / Retrofits / Maps (https://www.bimmerscene.com) +-- Forum: Bimmer Scene Coding & Navigation (https://www.bimmerscene.com/forumdisplay.php?fid=1) +--- Forum: BMW F / G Series Coding & Retrofits & Diagnostics (https://www.bimmerscene.com/forumdisplay.php?fid=3) +--- Thread: xHP Flashtool (/showthread.php?tid=1898) |
xHP Flashtool - Zombiedad - 09-09-2021 Hi guys, Really need some help here. New to the forum. I see lots of you are experts here. I have a 2011 F10 535i, car was running fine without any fault codes but recently I use the xHP Flashtool to code the transmission, after I coded it It shows the "Chassis Stabilization Failure". This error will disable my sport / sport+ mode. I can only drive normal mode. Some people say it could be the wheel speed sensor, but in ISTA software I don't see any option to check that. Also i think my car is little too old with the firmware/software. ISTA software update also grayed out. Is there way to update my car's module firmware/software. Even though delete the fault code. Within 1 min, the Chassis stabilization malfunction error will come back. I just want to get rid of that error and able to use sport/sport+ mode. Any help will be great. Thanks Ced xHP Flashtool - dmarctwm - 09-09-2021 Just coincidence, it s your dampers EDC Sent from my SM-G998U using Tapatalk RE: xHP Flashtool - Zombiedad - 09-09-2021 (09-09-2021, 05:39 PM)dmarctwm Wrote: Just coincidence, it s your dampers EDChummmm I don't think mine is EDC. I don't see any button or settings for that. I think my car needs to do software update. Do you know how to do it ? May be this will clear the Chassis Stabilization Malfunction error. I just ordered a tester. Wanna see if my wheel speed sensor is functioning. Since ISTA can't do any test to it (I don't see any where I can test It) xHP Flashtool - dmarctwm - 09-10-2021 You have pm Sent from my SM-G998U using Tapatalk RE: xHP Flashtool - Dkvinyls - 10-25-2021 (09-09-2021, 05:52 PM)Zombiedad Wrote:(09-09-2021, 05:39 PM)dmarctwm Wrote: Just coincidence, it s your dampers EDChummmm I don't think mine is EDC. I don't see any button or settings for that. I got an error after flashing my F31 with xHP, not the same as yours but it was immediate after flashing the transmission and it was obvious it wasn't a true fault. Whenever the automatic engine stop/start functions I get a Transmission overheat warning on the iDrive. xHP have confirmed that its the iSTEP version of the car being below what xHP expects to see, local independent BMW specialist quoted £108 to flash the car to the latest version. Well worth the money to me as I don't fancy carrying out a 7 hour flash of all modules by myself. RE: xHP Flashtool - Fatalix - 10-25-2021 It is generally always a good reminder to get your original software updated to the latest before any tune to DME/DDE or EGS is done - this will also 9/10 times avoid your dealer to perform a software update that will delete your tune, as it is always recognized as being the newest possible. At least for all F and E series by now. RE: xHP Flashtool - Fadeev34 - 12-13-2021 If someone has such problems, I can fix it remotely. RE: xHP Flashtool - Zombiedad - 12-13-2021 (12-13-2021, 10:34 PM)Fadeev34 Wrote: If someone has such problems, I can fix it remotely. I have the problem with the Chassis Stabilization Malfunction error. I can't use the sport mode. Every time when I start the engine, it shows "Chassis Stabilization Malfunction". Do you think you can fix it ? I think the modules in my car needs to be updated, but I don't wanna spend like 6 or more hours doing the update. Car is running fine except I can switch to sport + mode. Very annoying. xHP Flashtool - dmarctwm - 12-14-2021 Do you have EDC suspension ? Sent from my SM-G998U using Tapatalk |