BMW ISTA-D 4.49.23 Standalone Activated - Torrent

[Szabunio]

ISTA Standalone 4.49.23 Aktywowane.
To dzieło grupy wspaniałych ludzi z sąsiedniego forum, po prostu umieściłem łatkę i pliki w formacie Torrent, aby ułatwić korzystanie.
Link do torrenta:

[Ukryj]Treść jest ukryta! Sprawdź oryginalny post, aby go zobaczyć.[/ukryj]

MEGA link z plikami językowymi CZ, DE, FR, PL:
[Ukryj]Treść jest ukryta! Sprawdź oryginalny post, aby go zobaczyć.[/ukryj]

Uruchom instalator, przetestuj. Jeśli nie zadziała, zamień plik konfiguracyjny na ten dostarczony w folderze.

Dziękuję, to jest niesamowite!

[arcaneprokup]

Thank You!!!!!!!!

[Gari]

ISTA Standalone 4.49.23 Activated.
This is the work of a group of wonderful people from the neighboring forum, I just put the patch and files in Torrent format for easier use.
Link to torrent:

You have not unlocked this post's content yet. Please reply to this thread to unlock the content.

MEGA link with CZ, DE, FR, PL language files:

You have not unlocked this post's content yet. Please reply to this thread to unlock the content.

Run the installer, test. If it doesn't work, replace config file with provided one in the folder.

Thank you

[ir655]

Got this installed and working but have experienced a weird bug where the Terminal 30 and 15 voltages stop reporting after reaching around 13.4V. For the most part this doesn't really matter but can be an issue when an ignition changeover is required. Once the voltages reach 13.4 they get stuck there, and will not begin reporting correctly until the ICOM is released from ISTA. I have tried swapping out Ediabas for a fresh install but the issue persists. I expect its somewhere within the cracked ISTAGUI exe itself.

Everything else seems to be working as it should and vehicle identification works properly. Most people probably aren't even looking to use this with an ICOM, but if you are I have found ISTA Standalone 4.39.20 to be the most reliable. 

---

installed but in vehicle interface settings i don't have the option to select connect using default ediabas bin file. only shows local icom/enet option.

update. figured it out.

This is most likely determined based on which options you chose when you ran the installer. There are checkboxes on either the 2nd or 3rd step that allow you to install the additional interfaces and all are selected by default i believe. Try to re-install again.

Most these issues are due to ICOM firmware not being updated with this version of ISTA. Have you updated ICOM firmware?

[Ads_ali]

Hi can you send the details to download ista

[yardbro]

Got this installed and working but have experienced a weird bug where the Terminal 30 and 15 voltages stop reporting after reaching around 13.4V. For the most part this doesn't really matter but can be an issue when an ignition changeover is required. Once the voltages reach 13.4 they get stuck there, and will not begin reporting correctly until the ICOM is released from ISTA. I have tried swapping out Ediabas for a fresh install but the issue persists. I expect its somewhere within the cracked ISTAGUI exe itself.

Everything else seems to be working as it should and vehicle identification works properly. Most people probably aren't even looking to use this with an ICOM, but if you are I have found ISTA Standalone 4.39.20 to be the most reliable. 

---

installed but in vehicle interface settings i don't have the option to select connect using default ediabas bin file. only shows local icom/enet option.

update. figured it out.

This is most likely determined based on which options you chose when you ran the installer. There are checkboxes on either the 2nd or 3rd step that allow you to install the additional interfaces and all are selected by default i believe. Try to re-install again.

Most these issues are due to ICOM firmware not being updated with this version of ISTA. Have you updated ICOM firmware?

Yes, ICOM is on 04-24-11. Everything working normally on 4.39.20, but 4.49.20 has the voltage reporting issue only when using a maintainer on the car.

[julien381]

thank you very much

[hoster28]

Thank you for sharing

[Kindle5867]

thank you fella.

[metixso]

thank you very much