Hi,
Everyone~
I am alex~
I am from malaysia and currently venture into bmw repairing~

hi everybody new member big shout out to everyone, hopefully i will gain new knowledge and contribute in this forum
i am tech and looking to up knowledge on coding as i am myself a big fan of bmw  currently driving an X5 40e

Hello Community,

I need some help coding/activating my newly installed tow hitch.
I've installed it today, and wanted to code it with ÎŜ†Ä... but that only works with an ÏçØɱ which I don't have.

But seems it can also be done with ėšÝ§.

Can anyone provide step-by-step instructions - prefrably with screenshots- on how to achieve this?

Thanks in advance!

HELLO I HAVE A BMW F22 AND NEED SOME HELP WITH CODING THE FOLLOWING ISSUES I WOULD APPRECIATE ANY GUIDANCE:


803220 ULTRASONIC SENSOR REAR OUTER RIGHT SENSOR FAULT PROGRAMMING

930901 DRIVERS AIRBAG INTERVAL STAGE 1 SHORT CIRCUIT TO EARTH

930913 FRONT PASSENGER AIRBAG STAGE 1 SHORT CIRCUIT TO EARTH

930966 SEAT BELT TENSIONER REAR RIGHT CODING DATA DO NOT MATCH EQUIPTMENT

9309B8 PEDESTRIAN PROTECTION SYSTEM REAR LEFT RESISTANCE TOO HIGH

9309BE PEDESTRIAN PROTECTION SYSTEM REAR RIGHT RESISTANCE TOO HIGH

9309C4 DRIVERS SEAT BELT BUCKLE CONTACT OPEN CIRCUIT

930A91 PEDESTRIAN PROTECTION (OPTIC FIBRE) SENSOR FRONT CENTRE COMMUNICATION FAULT

930B12 PEDESTRIAN PROTECTION (OPTIC FIBRE) SENSOR SENDS FAULT

930B1A PEDESTRIAN PROTECTION (OPTIC FIBRE) SENSOR INTERNAL FAULT

930BA4 ACSM INTERNAL CONTROL UNIT FAULT

CF3192 SIGNAL STATUS OF DRIVER SEAT BELT BUCKLE SWITCH 0X297 INVALID TRANSMITTER ACSM

D90D16 LIGHT OPERATING UNIT (BEL) (LIN) WRONG VARIANT INSTALLED

SEAT HEATING FRONT PASSENGER MISSING LIN COMPONANT

SEAT HEATING FRONT DRIVER MISSING LIN COMPONANT

I HAVE A BMW M2 AIRBAG MODULE IN IF THIS MAKES ANY DIFFERENCE I KNOW THEY HAVE AN EXTRA KNEE AIRAG BUT I WOUL LIKE TO CODE THIS OUT IF POSSIBLE

HELLO DOES ANYONE KNOW HOW I CAN CODE BMW F22 HEATED AND POWER MEMORY SEATS TO A BMW F22 WITH ONLY HEATED SEATS FUNCTION ORIGINALLY?

Hello one more in the community

• Had my 1 Series F21 2016 for 6 months now and it came with custom headlights which are great apart from one issue that I've put up with, it keeps flagging an error on Idrive that there’s a fault with the “Side/daytime Lights” & “Headlight Aim Control”. Just to be clear, my lights are absolutely fine so I don’t understand how i’m getting this error. 

• On Auto it seems to be the worst so i tend to flick between side and main lights otherwise the chime of death will destroy my sanity. I’ve since spoke to place who put these LED’s in and they gave me the message below:

• “I've just had a look the job card, long story short we had a new set of original F22 headlights supplied to us that we did the conversion to and then fitted to the car as the original headlights were in a bit of mess and not usable (F20 internals hacked into a F22 casing)Both ourselves and another coder had a look but couldn't get anywhere as it's something that was relatively new at the time.”

• LWR system faulty - 8041B6

• Daytime driving lights: Open circuit 805CBC

• Parking light: Function defective: 805CE7

• Side Lights: Function defective: 805CEB

• Welcome lights: Function defective: 805CEE

• Daytime driving lights: Function defective: 805CB2

• Daytime driving lights: Open circuit: 805Е3С

• Parking light: Function defective: 805E67

• Side lights: Function Defective: 805E6B

• Welcome lights: Function defective: 805E6E

• Daytime driving lights: Function defective: 80532LIN:

•  General fault signal timeout: DAOCOO

• Led output 2: strand break: 4401FC

• ===

• I have since bought Bimmercode and coded out the headlight aim control as they are on LED’s(not surer why this wasnt done) and I’ve had some errors go but i’m still getting the side/daytime lights error in iDrive.

• Please, for the love of god..can someone tell me how I can code out my car checking the lights so this error goes away?I was suggested the below but it was already set to this.

• FEM

• 3061

• TFL_L and TFL_RKALT (Set to nicht_aktiv)WARM (Set to nicht aktiv)LED (Set to aktiv)

• Really appreciate your feedback!

Hi, my name is Adrian and I love cars...I own a BMW 525xd F11.

Hey Guys,

I tried to Flash my EGS with Alpina Software,
I changed the Typeschlüssel, Zeitkriterium and SALAPA
on first try I started the flash on TAL-Processing without selecting SVT_Soll JUST with FA and TAL, it failed but after the fail I just deleted all errors and the Car was finde.

On the second try I also selected SVT_soll on TAL-Processing, selected EGS and tried to Flash and it failed once more.

Now I have the problem when I read the Car with ÎŜ†Ä some ECUs dont communicate and I have some error codes and also Transportmode codes



The Car runs fine, everything is working and no Dashboard lights.

What should I do now, how to solve this problem?

Thanks!!

hi guys, joined the forum for advice and info. looking to primarily use ėšÝ§ to lower rear air suspension f11 after coilovers (on the front) are installed in a few weeks. I've downloaded ėšÝ§ 3.30 but need the psdzdata i think? any advice appreciated and welcomed 

cheers