Hey folks, I hope someone can help me out.
I’ve got an F36 LCI with adaptive headlights, and I’d like to adjust the brightness of the daytime running lights, both front and rear.

I tried doing this with BimmerCode before, but the DRLs didn’t change brightness at all, and I couldn’t adjust the tail light brightness either. So now I’ve downloaded ėšÝ§ with PSdZData and want to tackle it that way.

Can anyone walk me through it or point me in the right direction?

Shoutout to userfane

Hi, I'm Fábio, a mechanical engineer, I'm an engine calibrator, I want to learn about ėšÝ§, I'll be very happy to contribute to this forum!

Hello

Could someone please share a ncd from a working retrofit of the large screen on entrynav HU? i3 pre-LCI. I've tried with bimmercode and BU but I always get the 2/3rds screen and DTC 
"B7F87F HU-B: encoding fault"
"B7F8CB CID: Image data invalid or faulty"
psdz: 4.55.21
ėšÝ§: 24.06.01
HU FW level 03.11.20

Maybe I should try other versions of ėšÝ§ and psdz? 

Hey,
Need registration code for my HWID
93E9C9-33B21C

Hi there 

I'm Loïc from Switzerland, 21 yrs ago and looking to get some useful mods done with my Daily (BMW 120d xDrive, f20 from 2014).

Looking forward to see y'all around.

Best regards
Loïc

Hello everyone,

I'm new to this forum and it's my first time using ÎŜ†Ä.

I’m running into an issue with ÎŜ†Ä after adding programming data.

Setup:
- ÎŜ†Ä version: 4.52.40 (working fine before)
- Connection: ENET (E-Series DK CAN cable also tested)
- PSdZData path: C:\EC-APPS\ÎŜ†Ä\PSdZ\data\psdzdata
- Using ÎŜ†Ä-Patcher 2.3.5

Problem:
ÎŜ†Ä was working perfectly for diagnostics and fault clearing.
After adding PSdZData and modifying the registry entries for programming (BLPDataPath, SDPDataPath, SWIDataPath), I started getting this error when connecting to the car:

**Sec4Diag.OtherExceptions (Powered by ÎŜ†Ä-Patcher 2.3.5)**

The vehicle is detected correctly, but connection for diagnostics or programming fails.

What I found:
- My PSdZData folder is missing the **SWI** folder.
- I’m currently using the **Lite version** of PSdZData (contains mainseries, swe, mapping, etc., but no swi).
- If I disable “Programming” in ÎŜ†Ä settings, everything works again (diagnostics and fault reading are fine).

Questions:
1. Is the missing SWI folder the direct cause of this error?
2. Can I fix this temporarily by creating a dummy SWI folder, or do I need the full PSdZData package?
3. If yes, can someone confirm which full PSdZData version matches ÎŜ†Ä 4.52.40 or 4.55.21?
4. Is ÎŜ†Ä-Patcher 2.3.5 still compatible with ÎŜ†Ä 4.52+ or should I upgrade to 2.3.8 / 2.4.0?

Thanks in advance for any insights.
It’s strange that everything works perfectly until programming is enabled, so it seems clearly related to PSdZData structure or Patcher compatibility.

So you have an error code that says that the lens heating (lensheizung) on your ACC2 (adaptive cruise controll) radar sensor is broken. So now your cruise Control isn't working at all.


I'm going to tell you how you can turn off the lens heating function completely, if you can live with it not working in heavy snow and ice.
The lens heating is actually only turned on in temperatures between +5°C to -5°C.


Wanings:
1. I am not responsible if you break anything in your car
2. This is only for people who know how to code usual stuff.

First of all you will need to have NCS expert and NCS dummy installed and working properly.



1. Backup the following files from daten/E65 daten/E60 daten/e89 folder:
it is the corespondent file for wich model you want to code the lens heating


!!!!!!! MADE A BACK UP OF !!!!!!!!!!!
E65CVT.000 (e65) - E60CVT.000 (e60) - E89CVT.000 (e89)
ACC2_E60.C28 (or whatever your ACC2 module is)
SWTFSW02.dat (e65) - SWTFSW05.dat (e60) - SWTFSW03.dat (e89)



Code:


Code:
E65CVT.000 (e65) - E60CVT.000 (e60) - E89CVT.000 (e89)

ACC2_E60.C28 (or whatever your ACC2 module is, it could be ACC2_E60.C23 , etc.)

SWTFSW02.dat (e65) - SWTFSW05.dat (e60) - SWTFSW03.dat (e89)



2. Disassemble SWTFSW02.dat (e65) - SWTFSW05.dat (e60) - SWTFSW03.dat (e89)using NCS Dummy.

Add the following and reassemble.*



Code:


Code:
SWT_EINTRAG : 1700 "LENSHEIZUNG"



3. Disassemble E65CVT.000 (e65) - E60CVT.000 (e60) - E89CVT.000 (e89)

under*GRUPPE : {"Codierung_ACC"}*add the following and reassemble.





Code:


Code:
FSW_PSW : 1700 0007 // LENSHEIZUNG aktiv



4. Disassemble ACC2_E60.C28 or whatever your ACC2 module is and edit the following coding line located below "DYNAMIK_FLAG_ACC2" and above "NAVI_KOPPLUNG" (in between them) from looking like this:





Code:


Code:
PARZUWEISUNG_FSW : {00003003} 0000000F 0001 100C {} (02) {h} {} // DYNAMIK_FLAG_ACC2
PARZUWEISUNG_PSW1 : 0007 (01) // aktiv
PARZUWEISUNG_PSW1 : 000B (00) // nicht_aktiv
UNBELEGT1 : {00003003} 0000000F 0001 {} (04)
UNBELEGT2 : (01)
UNBELEGT1 : {00003003} 0000000F 0001 {} (08)
UNBELEGT2 : (01)
PARZUWEISUNG_FSW : {00003003} 0000000F 0001 0ED3 {} (10) {h} {} // NAVI_KOPPLUNG
PARZUWEISUNG_PSW1 : 0008 (00) // wert_01
PARZUWEISUNG_PSW1 : 0026 (00) // wert_02
PARZUWEISUNG_PSW1 : 0027 (00) // wert_03
PARZUWEISUNG_PSW1 : 0021 (01) // wert_04
PARZUWEISUNG_PSW1 : 00B6 (00) // wert_05



It should be edited to look like this:





Code:


Code:
PARZUWEISUNG_FSW : {00003003} 0000000F 0001 100C {} (02) {h} {} // DYNAMIK_FLAG_ACC2
PARZUWEISUNG_PSW1 : 0007 (01) // aktiv
PARZUWEISUNG_PSW1 : 000B (00) // nicht_aktiv
UNBELEGT1 : {00003003} 0000000F 0001 {} (04)
UNBELEGT2 : (01)
PARZUWEISUNG_FSW : {00003003} 0000000F 0001 1700 {} (08) {h} {} // LENSHEIZUNG
PARZUWEISUNG_PSW1 : 0007 (01) // aktiv
PARZUWEISUNG_PSW1 : 000B (00) // nicht_aktiv
PARZUWEISUNG_FSW : {00003003} 0000000F 0001 0ED3 {} (10) {h} {} // NAVI_KOPPLUNG
PARZUWEISUNG_PSW1 : 0008 (00) // wert_01
PARZUWEISUNG_PSW1 : 0026 (00) // wert_02
PARZUWEISUNG_PSW1 : 0027 (00) // wert_03
PARZUWEISUNG_PSW1 : 0021 (01) // wert_04
PARZUWEISUNG_PSW1 : 00B6 (00) // wert_05



5. Reassemble the files with NCS dummy.



6. Replace your original files with the reassembled ones.



7. Using NCS Expert read your ACC2.



8. Find the function*LENSHEIZUNG *

it is set to aktive (value 01) by default. (Which means that lens heating is turned on)



9. Change it to nicht_aktiv  or automatic ( the value should be 00) and code.



10. Done


Good Luck !

Hi guys!

Somehow i just now stumbled over this forum and i noticed that it has a TON of useful information & software. 
I'm 26 myself and a hobbyist, but got quite a bit of experience on older bimmers. E39/46 etc. 

Daily: 1999 E39 523i Sedan - 548000km on the clock
Nr2: 2003 E39 525D Wagon - 380000km
Nr3: 2002 E39 530DA Sedan - 360000km

Thanks for having me here!

BR Nev