a customer -> now friend of me has huge problems with his F10 2015 and me as the coder/programmer lost already nerves and 30h+ on this car.
What was the initial problem?
Water ingress in both front headlights, he has full adaptive LED headlights without bulbs. Before he came to me, he already had broken modules a few months ago and programmed somewhere else. It seemed for me like they didn't properly clean up and just change modules.
Although I coded a lot of E-Series, never had the chance to code F-Series. Now this time I had the chance to install and get ėšÝ§ running and learn coding → now I coded already a few F´s =)
Now, what did I do till now?
The First time the car came (Dec2020), the right TMS was dead and both LHM modules were partly functioning. We installed new parts, cleaned Headlights properly and I put the new module to the bad conditioned front left headlight, so the TMS module of the left one which was working before was installed in the right headlight.
The programming part was like "detect caf for swe", I then selected CAFD similar to my I-Level.
Hit code, and it should have coded standard coding to the module.
I did this for all new Modules.
After that I adapted LEDs in ÎŜ†Ä+ and it worked for like a week, then we had front right Indicator malfunction message with fast flashing indicators on the right side, turned out that the old one from the left headlight which we installed on the right had problems with the indicator. We ordered a new TMS Module, and while we started getting the car in the garage, the left indicator also stated malfunction with the previous new TMS module from Dec2020). We had the car not moved for a week, it was just standing outside the workshop.
We changed right TMS module, coded it and relearned indicators(where left sometimes threw error during learning). The right headlights' indicator worked fine where the left one was working only for two minutes and then flashing faster quitting with malfunction message on the dashboard. Clearing errors wouldn't get it working back, either you removed headlight and wait a few minutes or disconnect FRM and reconnect. It then did work for 2 minutes or so.
Yesterday, we received a new left indicator module and a used FRM(as i suspect somehow the FRM), however after installing the indicator module, nothing has changed, and we still struggled with the same error.
This time the error changed a bit, the ÎŜ†Ä+ learning passes without an error for the left one, but throws one for the right but disappears once ÎŜ†Ä+ does ignition changeover.
The left one immediately throws an error after one blinking cycle whereas the right one works fine.
I wanted to change FRM3 as I suspect it for being the problem, however the donor part is from 2010-11, I could install CAFD from 2013 and code it, but the original one is I-Level 2015.
With that FRM the headlights didn't work, its also not same parts numbers. Can it be flashed to 2015 Level or do I need to flash whole car?
Can we disable somehow the error recognition of LEDs, I tried some things in TMS with FDL coding, but it didn't work.
My friend ordered another TMS now, and it will arrive tomorrow, but maybe someone does have an idea to fix this via soft update, coding or just disabling cold/warm bulb/led checks.
Can i program in ÎŜ†Ä+??? as ISTAP tells me it is for E-Series but my ÎŜ†Ä+ Programming section is greyed out, do I need to try it with ÏçØɱ to enable that menu?
I have for now KDCAN + ENET and borrowed one ÏçØɱ-A, which I will try tomorrow in ÎŜ†Ä+.
Sorry for so much information, but I better tell the whole story than giving you guys partly the information you need to help me.
Off course, I tried so many things which I even don't remember or can't write as it will confuse you guys more.
I have an E90 Manual Transmission, ECU get damaged. I bought a used ECU but from an Automatic car. I make ISN etc all ok, car started perfect but I don't have acceleration ( acceleration is very late, have to floor pedal it will go slowly to 6 000 RPM).
I have this DTC:- 3099 No message EGS, receiver DME, transmitter ESG/SMG/DKG - Active
Any idea how to get it fixed. I think ECU is waiting for a signal from EGS which is not present.
Its been awhile since I coded my BMW (now sold) and just found a Mini that I had to have. 2019 Cooper S Signature with only 6000 miles! Now I want to get into it and see what I can add.
In my BMW I had upgraded the HU to an Android touch screen. I would like to bring the Mini to the 8.8 touch screen. Anyone out there have any experience with the Android retro fits?
thank you for the add into the group. i have a 06 530xi and im looking to download the ÎŜ†Ä program and get started with diagnostics. I have a Dcan+ cord on the way but wont have it for a couple days yet? If any one can give me any pointers it would be greatly appreciated thankyou. This is my first bmw/laptop mission. I am a marine mechanic and perform all mechanical jobs on my car myself but im totally new to bmw diagnostics. thanks.. i hope this message isnt to long ive never posted on here before
Hello everyone I am looking for a solution how to disable Sanity Check(VO coding) via SSH. I understand it's secret so I can pay for the information. Thank you Regards!
Hello everyone, I am new here, one question if someone can Help Me, I have Changed frm modul on x3 f25, now everything work but I have a Lot of failure, light faul, can someone Help me to code IT if is it possible with ėšÝ§? Many Thanks.
