Posts: 28
Threads: 2
Joined: Dec 2021
Reputation:
0
Country:
Hey guys,
I have a BMW F45 with ENTRYNAV without MOST port. I wish to change to another ENTRYNAV HU with MOST port so I can retrofit 6WA kombi.
Is it possible to exchange the headunit and use FSC repair kit from the old HU to the new HU?
Can anyone guide me how to do this? Need to virginize the donor HU first?
•
Posts: 678
Threads: 11
Joined: Dec 2022
Reputation:
192
Country:
have you managed to do the swap?
ECU Remap Stage 1 / 2
Checksum Correction
PopCorn / Hard Cut Limiter
ECU Cloning
PopsBangs
Launch Control Activation
E85 Conversion
DPF / EGR / Adblue / NOX / Lambda and many more.
•
Posts: 28
Threads: 2
Joined: Dec 2021
Reputation:
0
Country:
(04-20-2023, 02:08 AM)adelin731 Wrote: have you managed to do the swap?
Yes I bought a used ENTRYNAV with MOST port.
First I cleared FSC, VIN with Tool32
Then injected CAFD and coded with E-SYS
Used E-SYS to add FSC from FSC Repair kit
Everything works except I don't have older map file (<2018) to activate navigation. Because my repair kit FSC for the map is too old
•
Posts: 678
Threads: 11
Joined: Dec 2022
Reputation:
192
Country:
(05-26-2023, 03:35 AM)maxxsp Wrote: (04-20-2023, 02:08 AM)adelin731 Wrote: have you managed to do the swap?
Yes I bought a used ENTRYNAV with MOST port.
First I cleared FSC, VIN with Tool32
Then injected CAFD and coded with E-SYS
Used E-SYS to add FSC from FSC Repair kit
Everything works except I don't have older map file (<2018) to activate navigation. Because my repair kit FSC for the map is too old I swapped my head unit also, but I got the hu_champ2 and I'm not able to get the navigation working because my fsc codes are rejected
Will I be able to get tool32 on it now once is already coded to the car?
ECU Remap Stage 1 / 2
Checksum Correction
PopCorn / Hard Cut Limiter
ECU Cloning
PopsBangs
Launch Control Activation
E85 Conversion
DPF / EGR / Adblue / NOX / Lambda and many more.
•
Posts: 28
Threads: 2
Joined: Dec 2021
Reputation:
0
Country:
05-26-2023, 07:20 AM
(This post was last modified: 05-26-2023, 07:21 AM by maxxsp.)
(05-26-2023, 05:58 AM)adelin731 Wrote: (05-26-2023, 03:35 AM)maxxsp Wrote: (04-20-2023, 02:08 AM)adelin731 Wrote: have you managed to do the swap?
Yes I bought a used ENTRYNAV with MOST port.
First I cleared FSC, VIN with Tool32
Then injected CAFD and coded with E-SYS
Used E-SYS to add FSC from FSC Repair kit
Everything works except I don't have older map file (<2018) to activate navigation. Because my repair kit FSC for the map is too old I swapped my head unit also, but I got the hu_champ2 and I'm not able to get the navigation working because my fsc codes are rejected
Will I be able to get tool32 on it now once is already coded to the car?
If your other FSC codes are working then there should be no need to wipe the HU with tool32 again. You can check FSCstatus in E-SYS to confirm your HU correctly reports your vehicle vin.
I think you are facing the same problem as me. Your replacement HU has a map loaded on it that is not valid with your FSC.
In my case the replacement HU has europe map data so my repair pack FSC code (for southeast asia map) cannot activate. I either need to buy new ROUTE FSC for 2022 map update or find the older map file.
In your case you can generate new FSC for MOVE map using FSC generator and use the latest map file.
•
Posts: 678
Threads: 11
Joined: Dec 2022
Reputation:
192
Country:
(05-26-2023, 07:20 AM)maxxsp Wrote: (05-26-2023, 05:58 AM)adelin731 Wrote: (05-26-2023, 03:35 AM)maxxsp Wrote: (04-20-2023, 02:08 AM)adelin731 Wrote: have you managed to do the swap?
Yes I bought a used ENTRYNAV with MOST port.
First I cleared FSC, VIN with Tool32
Then injected CAFD and coded with E-SYS
Used E-SYS to add FSC from FSC Repair kit
Everything works except I don't have older map file (<2018) to activate navigation. Because my repair kit FSC for the map is too old I swapped my head unit also, but I got the hu_champ2 and I'm not able to get the navigation working because my fsc codes are rejected
Will I be able to get tool32 on it now once is already coded to the car?
If your other FSC codes are working then there should be no need to wipe the HU with tool32 again. You can check FSCstatus in E-SYS to confirm your HU correctly reports your vehicle vin.
I think you are facing the same problem as me. Your replacement HU has a map loaded on it that is not valid with your FSC.
In my case the replacement HU has europe map data so my repair pack FSC code (for southeast asia map) cannot activate. I either need to buy new ROUTE FSC for 2022 map update or find the older map file.
In your case you can generate new FSC for MOVE map using FSC generator and use the latest map file. I never wiped the hu, I just bought it and VO coded to the car, that's all. So, if I'm right, I need to wipe it with tool32, then vo code and after that use the fsc repair kit. Do you mind explaining to me step by step, I never had to deal with maps and fsc codes. Thanks in advance.
ECU Remap Stage 1 / 2
Checksum Correction
PopCorn / Hard Cut Limiter
ECU Cloning
PopsBangs
Launch Control Activation
E85 Conversion
DPF / EGR / Adblue / NOX / Lambda and many more.
•
Posts: 28
Threads: 2
Joined: Dec 2021
Reputation:
0
Country:
(05-26-2023, 09:54 AM)adelin731 Wrote: (05-26-2023, 07:20 AM)maxxsp Wrote: (05-26-2023, 05:58 AM)adelin731 Wrote: (05-26-2023, 03:35 AM)maxxsp Wrote: (04-20-2023, 02:08 AM)adelin731 Wrote: have you managed to do the swap?
Yes I bought a used ENTRYNAV with MOST port.
First I cleared FSC, VIN with Tool32
Then injected CAFD and coded with E-SYS
Used E-SYS to add FSC from FSC Repair kit
Everything works except I don't have older map file (<2018) to activate navigation. Because my repair kit FSC for the map is too old I swapped my head unit also, but I got the hu_champ2 and I'm not able to get the navigation working because my fsc codes are rejected
Will I be able to get tool32 on it now once is already coded to the car?
If your other FSC codes are working then there should be no need to wipe the HU with tool32 again. You can check FSCstatus in E-SYS to confirm your HU correctly reports your vehicle vin.
I think you are facing the same problem as me. Your replacement HU has a map loaded on it that is not valid with your FSC.
In my case the replacement HU has europe map data so my repair pack FSC code (for southeast asia map) cannot activate. I either need to buy new ROUTE FSC for 2022 map update or find the older map file.
In your case you can generate new FSC for MOVE map using FSC generator and use the latest map file. I never wiped the hu, I just bought it and VO coded to the car, that's all. So, if I'm right, I need to wipe it with tool32, then vo code and after that use the fsc repair kit. Do you mind explaining to me step by step, I never had to deal with maps and fsc codes. Thanks in advance. Open Tool32 and load your HU file "champ2.prg"
- Find job: steuern_persistency_clear (might be a variation of this depending on HU type)
- Type 0x01 in the argument box
- Double click on job to run
Then use E-SYS, Comfort mode>FSC to load your repair pack certs and install FSC codes
•
Posts: 678
Threads: 11
Joined: Dec 2022
Reputation:
192
Country:
(05-26-2023, 11:17 AM)maxxsp Wrote: (05-26-2023, 09:54 AM)adelin731 Wrote: (05-26-2023, 07:20 AM)maxxsp Wrote: (05-26-2023, 05:58 AM)adelin731 Wrote: (05-26-2023, 03:35 AM)maxxsp Wrote: Yes I bought a used ENTRYNAV with MOST port.
First I cleared FSC, VIN with Tool32
Then injected CAFD and coded with E-SYS
Used E-SYS to add FSC from FSC Repair kit
Everything works except I don't have older map file (<2018) to activate navigation. Because my repair kit FSC for the map is too old I swapped my head unit also, but I got the hu_champ2 and I'm not able to get the navigation working because my fsc codes are rejected
Will I be able to get tool32 on it now once is already coded to the car?
If your other FSC codes are working then there should be no need to wipe the HU with tool32 again. You can check FSCstatus in E-SYS to confirm your HU correctly reports your vehicle vin.
I think you are facing the same problem as me. Your replacement HU has a map loaded on it that is not valid with your FSC.
In my case the replacement HU has europe map data so my repair pack FSC code (for southeast asia map) cannot activate. I either need to buy new ROUTE FSC for 2022 map update or find the older map file.
In your case you can generate new FSC for MOVE map using FSC generator and use the latest map file. I never wiped the hu, I just bought it and VO coded to the car, that's all. So, if I'm right, I need to wipe it with tool32, then vo code and after that use the fsc repair kit. Do you mind explaining to me step by step, I never had to deal with maps and fsc codes. Thanks in advance. Open Tool32 and load your HU file "champ2.prg"
- Find job: steuern_persistency_clear (might be a variation of this depending on HU type)
- Type 0x01 in the argument box
- Double click on job to run
Then use E-SYS, Comfort mode>FSC to load your repair pack certs and install FSC codes That's great, but where do i get the hu file "champ2.prg" from?
ECU Remap Stage 1 / 2
Checksum Correction
PopCorn / Hard Cut Limiter
ECU Cloning
PopsBangs
Launch Control Activation
E85 Conversion
DPF / EGR / Adblue / NOX / Lambda and many more.
•
Posts: 28
Threads: 2
Joined: Dec 2021
Reputation:
0
Country:
05-26-2023, 03:22 PM
(This post was last modified: 05-26-2023, 03:22 PM by maxxsp.)
(05-26-2023, 11:19 AM)adelin731 Wrote: (05-26-2023, 11:17 AM)maxxsp Wrote: (05-26-2023, 09:54 AM)adelin731 Wrote: (05-26-2023, 07:20 AM)maxxsp Wrote: (05-26-2023, 05:58 AM)adelin731 Wrote: I swapped my head unit also, but I got the hu_champ2 and I'm not able to get the navigation working because my fsc codes are rejected
Will I be able to get tool32 on it now once is already coded to the car?
If your other FSC codes are working then there should be no need to wipe the HU with tool32 again. You can check FSCstatus in E-SYS to confirm your HU correctly reports your vehicle vin.
I think you are facing the same problem as me. Your replacement HU has a map loaded on it that is not valid with your FSC.
In my case the replacement HU has europe map data so my repair pack FSC code (for southeast asia map) cannot activate. I either need to buy new ROUTE FSC for 2022 map update or find the older map file.
In your case you can generate new FSC for MOVE map using FSC generator and use the latest map file. I never wiped the hu, I just bought it and VO coded to the car, that's all. So, if I'm right, I need to wipe it with tool32, then vo code and after that use the fsc repair kit. Do you mind explaining to me step by step, I never had to deal with maps and fsc codes. Thanks in advance. Open Tool32 and load your HU file "champ2.prg"
- Find job: steuern_persistency_clear (might be a variation of this depending on HU type)
- Type 0x01 in the argument box
- Double click on job to run
Then use E-SYS, Comfort mode>FSC to load your repair pack certs and install FSC codes That's great, but where do i get the hu file "champ2.prg" from?
It's from within the Tool32 installation, you need to open that file
•
Posts: 74
Threads: 0
Joined: Sep 2020
Reputation:
1
Country:
(05-26-2023, 09:54 AM)adelin731 Wrote: (05-26-2023, 07:20 AM)maxxsp Wrote: (05-26-2023, 05:58 AM)adelin731 Wrote: (05-26-2023, 03:35 AM)maxxsp Wrote: (04-20-2023, 02:08 AM)adelin731 Wrote: have you managed to do the swap? HI HOW DO YOU CLEAR FSC ON ENTRY NAV TO PUT THE REPAIR CODE
•
|