Hi all,

After using ė-šÝ§ for a long time to successfully program and flash modules, I now wanted to give ÎŜ†Ä+ a try.
I got the version 4.39.20 and it installed perfectly and also starts perfectly. I set the connection mode to ėšÝ§.
When I open the connection dialog, my ENET cable is listed with the VIN and IP of the car showing. I click that one, it starts loading, and then nothing.
Tabs like Vehicle Information are unlocked, but everything on that tab is simply empty. No list of ECU's, no data on the dashboard like mileage, vin, etc. Everything is - or empty.
What would be the cause of this? The cable should be good, I used it for years on ė-šÝ§ successfully. I also tried EDIABAS as connection method, verifying that the EDIABAS config file says ENET as method but that results in exactly the same behavior (though, no VIN showing in connection window but then after connecting it displays everything blank).

Kind regards and thank you in advance.

Hi to all
I'm Carlos from Portugal
I want to learn and help about coding Bmw car and motorrad.

Best regards

Hi, im Dan from UK/N54

Attached Files

Thumbnail(s)
   

Here's my E60 M5

I have been trying to get my ÏçØɱ to work with ÎŜ†Ä v4.39 but the firmware needs to be updated.
I spent a lot of time trying to find a suitable version, but unfortunately it didn't work.
Do any of you guys have the latest firmware?

Current PACKAGE IMAGE version:
03.15.00
Current SYSTEM IMAGE version:
01.26.00
Current APPLICATION IMAGE version:
01.41.00

Hello all!

I have quite a lot of trouble with my ENET cable on all G-series (haven't tried any F-s).
If I connect the ENET to car, turn on Diag Mode (ignition on) and plug the cable to my laptop and run ÎŜ†Ä+ (4.31.40 / 4.39.20 / 4.41.40 all tested) then I can see ENET with IP and car VIN and all seems OK, but "Read out Vehicle Data" will hang for 10+ minutes and then prompts for 7-digit VIN, because VIN can not be retrieved and then the check PAD active error pops also up.
Only way to connect is to unplug ENET from OBD, lock down car for whatever it takes for the car to go to sleep (red triangle off) and then open car, plug ENET to OBD and Diag Mode. Then ÎŜ†Ä will read the car.
Same story happens with ėšÝ§. Having to go through the "put the car to sleep" process is stupid and time consuming.
Especially that this was not needed about 1+ years ago. Has this something to do with some ZGM update?

OEM ÏçØɱ Next can connect everytime all the time...
Here comes the question - I have heard that you can not succesfully update software when the ÏçØɱ is connected with cable (LAN) and it needs to be connected in a wireless environment (Access Point or Router or whatever)? One software update failed on my G30 when updating the HU - I started to get a lot of EDIABAS errors and had to fix with ENET.

Goof afternoon gentleman,

I am from the netherlands, and have a tuning company for over 7 years.
Always liked reading the threads on this forum, so i finally made an account

Hi, is it possible to connect automatic transmition from a e53 on the bench with ÎŜ†Ä?
I can connect with launch and ÏÑÞÀ no problem, I want to check adaptation values of the clutches

Hi
Got ÎŜ†Ä via virtual box running on win 7, through win 10 on my laptop.
I have done everything that needs to be done to run it via enet, but when i try to connect to car, i just get a blank screen, i have watched every video possible to connect with enet, setting all correct, cable is good , but still cannot connect to f25. Does anyone else  have any ideas how to connect to the car.
Thanks in advance