Hello everyone and yes I’m a tad late to the party. I’m looking for some guidance in which software would be best to use on my 2005 pre LCI E60. She’s a 530D and an ex copper which means help from usual dealers and so called pros has been challenging to say the least. I have the dreaded restraint system errors and wondered what versions of things like Standard Tools, ÎŜ†Ä-D/P, or older like the DIS/SS software. Also which version SP Daten would correctly work with these older modules. I have a load of things already acquired software wise and I have the K/D-Can cable and also an ÏçØɱ A(clone with most controller). 

The faults displayed in the car show Restraint System Faulty; Front Passenger Airbags Faulty; Side Airbag Rear Left Faulty; Side Airbag Rear Right Faulty and Driver Restraint System Faulty. If ÏÑÞÀ or similar codes need to be here I can get that done no problem for anyone who may be able to shed any light.

At a point there were more of these but for some messing with NCS Expert I managed to whittle it down somewhat and this is what I'm left with. I have already tried the 2.2ohm bypass on the individual wiring to the modules and also the 3.3ohm is present in the BST but these faults remain and the warning lights are on the Dash which is now becoming most annoying. 

Unsure if this matters but someone may know, when I load NCS Expert and read my car, it's the only app that reads my VIN incorrectly by means of adding an H to the end which shouldn't be there it should end 90958 like every other app shows but 90958H is what NCS says. It also flags an issue with my VA saying that #0305 is incorrect for my Vehicle Order but when I try to amend it, I open VA, left click then press delete which removes it but it wont then re-write back to the car, stating a fault that I will re read today and post here.

On ÎŜ†Ä D regardless of which version, It seems to read all my modules and highlights similar, if not the same as DIS which is great but ÎŜ†Ä-P on the other hand( ÎŜ†Ä P SYS 3 55 0) it reads my VIN then scans the modules but then halts with the following error "The Connected Vehicle Has An Unknown Data Status ( E060-05-06-500, UNBENKANNTE I-STUFFE). This Cannot Be Handled with ÎŜ†Ä/P. Ensure that the current version of ÎŜ†Ä/P has been loaded or contact technical support."

The above error is only present in the ÎŜ†Ä/P version I have listed as all others have read the VIN and upon scanning the modules states " connection with the interface has been interrupted and the session must end " This error strangely enough also appears on SS (progman) that's on a different laptop with DIS and all VM's are set up and functioning as they should. 

Just to be clear, I have separate laptops for specific software's as not all run on same OS etc etc and also would not wish to disrupt the EDIABAS folder that whichever software installs( cross contamination   ) I am mindful that she is 18yrs old but if at all possible and MOT permitting I'd happily keep her another 18 lol but if this is a dead end I'll lick my wounds and cut my losses as she has served me impeccably well 

Everything I have learned about my car I have done so by reading trying failing reading more and more and for the most part I have had good success, but this one has me over a barrel lol so any help would be greatly received from whoever is up for the challenge 

Hi , just joined with the hope of learning more about My 2018 X3Goi . Hopefully I can get some information and also give some input.

Hello,
I'm looking for a tool for changing codes in r1250gs . Any expert in the room ??



Regards

Hi. Nice to meet you. Im happy Im here

Whenever I boot up ÎŜ†Ä I'm greeted with this screen and when I hit next it doesn't give me the option to hit a key, the entire box is blank. When googling this it all says that the version I'm trying to run shouldn't even need a license. What's even weirder to me is that I have this program installed on my computer and it works perfectly fine with no issues. But when I boot up ÎŜ†Ä on my laptop I'm greeted with this license screen. I don't understand why the same exact program isn't asking for a license on my PC but is on my laptop. I also already tried installing the requirements it states and standard tools.

Attached Files

Thumbnail(s)
   

Hi everyone, I have a BMW F31, I love to modernize it, but I want to know more and I hope to learn it here

Regards

Hoping that there would be a few out there that can assist in the following.
I attempted to update my brothers Service History on his Mini 2018 F56 by using Blackbox Service History Manager.
I have used this on my 116d BMW and it worked a treat.
On his car it stated that all was well but when the Head Unit rebooted the option to view Service History had disappeared.
Of cause he is not happy with me and I would like to see if I can get the history back again.

Update -
Tried another route by using HU-ServiceManager
Downloaded Java, configured the config file to point to it and also the Ediabas folder.
Copied the NBTEVO.prg file from my ÎŜ†Ä files over to the Ediabas ECU folder.
When connecting to the car it connects to the Head Unit OK.
Attempted to write the PDI entry and it states OK
Rebooted HU from HU-ServiceManager and the entry is not there.
It is missing the option to display Service History as per screenshot.
Does anyone know a way of getting this back?
Maybe checking the HU using ė-šÝ§ or Tool32?
Could be just a config setting?
Any assistance would be greatly received.
Jim

Attached Files

Thumbnail(s)
   

hi all,

glad to be here.
lucky owner of a X4 F26 30d

see you around the forum

Hello
Thank you for accepting me

I'm a proud owner of a 435d x drive my first BMW 

Regards
Paul

Hi!

I have G30 530xd.
Glad to be a member of this forum.

A