Hi @ll,

i need help. 
In my F46 i code with BU some options in my HU_ENTRYNAV. After pressing coding the display go black. 
HU do nothing.
ėšÝ§ dont find HU_ENTRYNAV and KOMBI. ÎŜ†Ä say no communication to Headunit and Kombi. Also ÎŜ†Ä says MOST ist broken.

What can I do? Why BU coding brick my HU? Can anybody help me?

ENET and VXDIAG i have to code and prograiming.

Hello, I'm looking for ÎŜ†Ä 4.28.22 and i found some torrent on google drive but unfortunately torrent is bad beacouse i have 1KB/s Could somebody share ÎŜ†Ä 4.28.22? What is the best stable ÎŜ†Ä? What about 4.39.2?
I appreciate!

Hello, i have a small problem with connecting to the car by ENET cable with ÎŜ†Ä 4.39.2. in connection manager there isn't my car shows. Before i was using 4.29 i think and i have no problems with it and ėšÝ§ same works good but 4.39 no :/

i have redist:
- 2005, 2008, 2010, 2012, 2013, 2015 - 2019

standard tools 2024.03 

i have this ÎŜ†Ä downloaded ÎŜ†Ä


and it looks like this 


easy connect normally showing my car. Could somebosy help why this version not work? in ediabas confif i tried ENET and REMOTE and nothing.

Hi everyone. 
Where can i get ėšÝ§ which works on G series? 
Could anyone please share download if there is one?

Hello, on bmw f25 frm i coded out sidemarkers. After every battery diconnection coding comes back to stock. Does anybody know what could be the problem ? Ive done few and first time having this issue )

Hello, could anybody tell me how to code lector language in f30 lci evo id5 ?

Hello everyone!

I have a question, if I code out the TPMS on F11 do I have to disconnect the RDC module manually? Or it won't matter after it's coded out?

Hi I'm new to the forum,

I just wanted to comment that I could sucessfully code some features to my G30 520d 2017 using the available PRO Launcher 2.8.1 from Tokenmaster.

Many people say that is impossible to code anything beyond istep 17-something and you need to spend money in the updated Launchers but, by updating the pszdata the car accepted the coding of the alpina kombi and disabling of the star-stop features.

Is there any problems using this older version I might run into if I attempt coding other ECU's? From what I understand the features not mapped will show as unknown meaning I will not be able to know what it is about but the ones already mapped for this version will show up and work without issues. Might be the case as far as I understand the memory holds the parameters in specific memory addresses and they rarely overwrite existing parameters with other so the existing ones work. But it might be the case that the same address in memory is used for other parameter in the updated istep firmware and that could mess up the ECU.

Anyone knows more about this topic? How exactly does the launcher and ėšÝ§ coding of parameters work?

Regards.

Have a NBT unit I bought from ebay that had ID4 loaded, I ran tool32 v850 clear, flashed to ID6 (1803) via ėšÝ§ and manually deleted persistance folders "rm -r /var/opt/sys/persistence/*" and "rm -r /net/hu-jacinto/var/opt/sys/persistence/*", but am unable to load full FSCs set via feature installer.. or USB .bin and FSC load. Not sure how I messed up the the unit, but any advice on what the unit might need to get it back to clean state?  Perhaps missed a virginzation step.. on I did run the set vin in ėšÝ§, and it matches my ZGW vin..

Thanks very much for any advice!

Hello,
I've just retrofitted the homelink(garage door opener) interior mirror to my BMW G20. Even though the retrofit kit mentions that everything is plug and play and no coding is needed, two faults were left after installation. Everything works perfectly except that these two faults are not cleared, neither with ÎŜ†Ä or any other program (Bimmerlink or other mobile apps). Can someone help me with the necessary coding to get rid of these two errors? This is the mirror that I've used 51162472237.
Thanks a lot.